|
|
|
|
Home / Computers / Computer Certification
Cisco CCNP Certification: Using The BGP Command “Update-Source”
By:Chris Bryant, CCIE #12933
When you start preparing for your CCNP exam, particularly the BSCI exam, you're introduced to Border Gateway Protocol (BGP) configurations. BGP is unlike any protocol you learned during your CCNA studies, and even the similarities are a little bit different!
BGP forms neighbor relationships, much like EIGRP and OSPF do. The interesting thing with BGP is that potential neighbors, or "peers", do not need to be directly connected and can use their loopback interfaces to form the peer relationships.
It may well be to your advantage to use loopbacks to form peer relationships rather than the actual interface facing the potential neighbor. This can be done because BGP uses static neighbor statements rather than any kind of dynamic neighbor discovery process.
Consider a router that has two paths to a BGP speaker. The interfaces are numbered like this:
Router1: Serial0, 172.1.1.1 /24, Serial2, 179.1.1.1 /24, loopback0, 1.1.1.1 /32.
Router2: Serial0, 172.1.1.2/24, Serial2 179.1.1.2/24, loopback0, 2.2.2.2 /32.
We could configure Router1 like this:
router bgp 200
neighbor 172.1.1.2 remote-as 200
In this case, BGP would automatically use 172.1.1.1 as the source for the TCP connection that has to be set up with the neighbor before updates can be exchanged; this address is known as the best local address. However, if the remote peer's serial0 interface is shut down or goes down for another reason, the peer relationship would be lost even though Router2 is still available.
Instead of using one of the physical interfaces, we can use the loopbacks on each router to establish the TCP-based peer connection. The configurations would look like this:
Router1:
router bgp 200
neighbor 2.2.2.2 remote-as 200
neighbor 2.2.2.2 update-source loopback0
Router2:
router bgp 200
neighbor 1.1.1.1 remote-as 200
neighbor 1.1.1.1 update-source loopback0
In this case, losing one of the physical connections does not necessarily mean the BGP peering is lost; as long as the routers have a valid path to each other's loopback addresses, the BGP peer relationship will stay in place. And better yet, we avoid the dreaded “single point of failure
Article Source: http://www.dailynewarticles.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (www.thebryantadvantage.com), home of free CCNA and CCNP tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages. Video courses and training, binary and subnetting help, and corporate training are also available. Pass the CCNA exam and CCNP exams with Chris Bryant, CCIE #12933!
More Articles from Computer Certification Category:
Cisco CCNP Certification / BCMSN Exam Tutorial: Writing QoS Policy
Cisco CCNP / BCSI Exam Tutorial: Configuring EIGRP Packet Authentication
Cisco CCNP / BSCI Certification: Introduction To ISIS Terminology
What To Expect When Taking Your First Cisco Certification Exam
Cisco CCNA / CCNP Home Lab: Why You Need An ISDN Simulator
Be Certifiable! The Basics Of MCSE And MCP
Cisco CCNP / BCSI Exam Tutorial: Broadcasts And The IP Helper-Address Command
Webroot Window Washer
Cisco CCNA / CCNP Home Lab Tutorial: Using 2520 Routers
CCNA / CCNP Home Lab Tutorial: The VLAN.DAT File
Cisco CCNP / BCMSN Exam Tutorial: Changing Root Bridge Election Results
CCNP Certification / BCMSN Exam Tutorial: HSRP MAC Addresses And Timers
Cisco CCNP / BCMSN Exam Tutorial: Switches, QoS, And Cisco's Networking Model
Cisco CCNA Exam Tutorial: Troubleshooting Directly Connected Serial Interfaces
How To Earn Cisco’s Firewall Specialist Certification
|
|
