|
|
|
|
Home / Computers / Computer Certification
Cisco CCNP / BCMSN Exam Tutorial: The Four (Or Five) STP Port States
By:Chris Bryant, CCIE #12933
As a CCNP candidate and a CCNA, you may be tempted to skip or just browse the many details of Spanning Tree Protocol. After all, you learned all of that in your CCNA studies, right? That's right, but it never hurts to review STP for a switching exam! Besides, many of us think of the four STP port states - but officially, there's a fifth one!
Disabled isn't generally thought of as an STP port state, but Cisco does officially consider this to be an STP state. A disabled port is one that is administratively shut down.
Once the port is opened, the port will go into blocking state. As the name implies, the port can't do much in this state - no frame forwarding, no frame receiving, and therefore no learning of MAC addresses. About the only thing this port can do is accept BPDUs from neighboring switches.
A port will then go from blocking mode into listening mode. The obvious question is "listening for what?" Listening for BPDUs - and this port can now send BPDUs as well. The port still can't forward or receive data frames.
When the port goes from listening mode to learning mode, it's getting ready to send and receive frames. In learning mode, the port begins to learn MAC addresses in preparation for adding them to its MAC address table.
Finally, a port can go into forwarding mode. This allows a port to forward and receive data frames, send and receive BPDUs, and place MAC addresses in its MAC table.
To see the STP mode of a given interface, use the show spanning-tree interface command.
SW1#show spanning-tree interface fast 0/11
Vlan Role Sts Cost Prio.Nbr Type
---------------- ---- --- --------- -------- ----------
VLAN0001 Desg FWD 19 128.11 P2p
To see these states in action, shut a port down in your CCNA / CCNP home lab and continually run the show spanning interface command. Once you see this in action on real Cisco equipment, you'll have no problem with BCMSN exam questions. Just don't practice this or any other Cisco command on a production network!
Article Source: http://www.dailynewarticles.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNP and CCNA tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages.
You can also join his RSS feed and visit his blog, which is updated several times daily with new Cisco certification articles, free tutorials, and daily CCNA / CCNP exam questions! Details are on the website.
For a FREE copy of his latest e-books, “How To Pass The CCNA” and “How To Pass The CCNP”, just visit the website! You can also get FREE CCNA and CCNP exam questions every day! Pass the CCNP exam with The Bryant Advantage!
More Articles from Computer Certification Category:
Cisco CCNP Certification / BCMSN Exam Tutorial: Writing QoS Policy
Cisco CCNP / BCSI Exam Tutorial: Configuring EIGRP Packet Authentication
Cisco CCNP / BSCI Certification: Introduction To ISIS Terminology
What To Expect When Taking Your First Cisco Certification Exam
Cisco CCNA / CCNP Home Lab: Why You Need An ISDN Simulator
Be Certifiable! The Basics Of MCSE And MCP
Cisco CCNP / BCSI Exam Tutorial: Broadcasts And The IP Helper-Address Command
Webroot Window Washer
Cisco CCNA / CCNP Home Lab Tutorial: Using 2520 Routers
CCNA / CCNP Home Lab Tutorial: The VLAN.DAT File
Cisco CCNP / BCMSN Exam Tutorial: Changing Root Bridge Election Results
CCNP Certification / BCMSN Exam Tutorial: HSRP MAC Addresses And Timers
Cisco CCNP / BCMSN Exam Tutorial: Switches, QoS, And Cisco's Networking Model
Cisco CCNA Exam Tutorial: Troubleshooting Directly Connected Serial Interfaces
How To Earn Cisco’s Firewall Specialist Certification
|
|
