 |
|
|
|
|
Home / Computers / Computer Certification
Cisco CCNP / BSCI Exam Tutorial: Configuring And Troubleshooting OSPF Virtual Links
By:Chris Bryant, CCIE #12933
Knowing when and how to create an OSPF virtual link is an essential skill for BSCI and CCNP exam success, not to mention how important it can be on your job! As a CCNA and CCNP candidate, you know the theory of virtual links, so let's take a look at how to configure a virtual link, as well as some real-world tips that many CCNA and CCNP study guides leave out!
In this configuration, no router with an interface in Area 4 has a physical interface in Area 0. This means a logical connection to Area 0, a virtual link, must be built.
In the following example, R1 and R3 are adjacent and both have interfaces in Area 0. R4 has an adjacency with R3 via Area 34, but R4 has no physical interface in Area 0 and is advertising its loopback 4.4.4.4 into OSPF. R1 doesn't have the route to that loopback.
R1#show ip route ospf
6.0.0.0/32 is subnetted, 1 subnets
O 6.6.6.6 [110/11] via 10.1.1.5, 01:05:45, Ethernet0
172.23.0.0/27 is subnetted, 1 subnets
O IA 172.23.23.0 [110/74] via 172.12.123.3, 00:04:14, Serial0
7.0.0.0/32 is subnetted, 1 subnets
O 7.7.7.7 [110/11] via 10.1.1.5, 01:05:45, Ethernet0
To resolve this, a virtual link will be built between R3 and R4 through Area 34. The area through which the virtual link is built, the transit area, cannot be a stub area of any kind.
R4(config)#router ospf 1
R4(config-router)#area 34 virtual-link 3.3.3.3
R3(config)#router ospf 1
2d07h: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 172.23.23.4, Ethernet0
R3(config)#router ospf 1
R3(config-router)#area 34 virtual-link 4.4.4.4
R3(config-router)#^Z
2d07h: %OSPF-5-ADJCHG: Process 1, Nbr 4.4.4.4 on OSPF_VL0 from LOADING to FULL, Loading Done
A few details worth noting... the virtual link command uses the remote device's RID, not necessarily the IP address on the interface that's in the transit area. Also, don't worry about that error message you see in the output from R3 that is normal and you'll see it until you finish building the virtual link.
Always confirm the virtual link with show ip ospf virtual-link. If you've configured it correctly, the VL should come up in a matter of seconds.
R3#show ip ospf virtual-link
Virtual Link OSPF_VL0 to router 4.4.4.4 is up
Run as demand circuit
DoNotAge LSA allowed.
Transit area 34, via interface Ethernet0, Cost of using 10
Transmit Delay is 1 sec, State POINT_TO_POINT,
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
Hello due in 00:00:00
Adjacency State FULL (Hello suppressed)
Index 2/4, retransmission queue length 1, number of retransmission 1
First 0x2C8F8E(15)/0x0(0) Next 0x2C8F8E(15)/0x0(0)
Last retransmission scan length is 1, maximum is 1
Last retransmission scan time is 0 msec, maximum is 0 msec
Link State retransmission due in 3044 msec
Virtual links are actually simple to configure, but for some reason they seem to intimidate people. It's my experience that the error message highlighted in R3's output above causes a lot of panic, but the only thing that message means is that you're not finished configuring the virtual link yet.
There are three main misconfigurations that cause 99% of virtual link configuration issues:
Using the wrong OSPF RID value
Trying to use a stub area as the transit area
Failure to configure link authentication on the virtual link when Area 0 is running authentication
That last one is the one that gets forgotten! A virtual link is really an extension of Area 0, and if Area 0 is running link authentication, the virtual link must be configured for it as well. Pay attention to the details. don't panic when you see the error message on the second router you configure with the virtual link, and you'll be ready for any virtual link situation on the job or in the CCNA / CCNP exam room!
Article Source: http://www.dailynewarticles.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNP and CCNA tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages.
You can also join his RSS feed and visit his blog, which is updated several times daily with new Cisco certification articles, free tutorials, and daily CCNA / CCNP exam questions! Details are on the website.
For a FREE copy of his latest e-books, “How To Pass The CCNA” and “How To Pass The CCNP”, just visit the website! You can also get FREE CCNA and CCNP exam questions every day! Pass the CCNP exam with The Bryant Advantage!
More Articles from Computer Certification Category:
Cisco CCNP Certification / BCMSN Exam Tutorial: Writing QoS Policy
Cisco CCNP / BCSI Exam Tutorial: Configuring EIGRP Packet Authentication
Cisco CCNP / BSCI Certification: Introduction To ISIS Terminology
What To Expect When Taking Your First Cisco Certification Exam
Cisco CCNA / CCNP Home Lab: Why You Need An ISDN Simulator
Be Certifiable! The Basics Of MCSE And MCP
Cisco CCNP / BCSI Exam Tutorial: Broadcasts And The IP Helper-Address Command
Webroot Window Washer
Cisco CCNA / CCNP Home Lab Tutorial: Using 2520 Routers
CCNA / CCNP Home Lab Tutorial: The VLAN.DAT File
Cisco CCNP / BCMSN Exam Tutorial: Changing Root Bridge Election Results
CCNP Certification / BCMSN Exam Tutorial: HSRP MAC Addresses And Timers
Cisco CCNP / BCMSN Exam Tutorial: Switches, QoS, And Cisco's Networking Model
Cisco CCNA Exam Tutorial: Troubleshooting Directly Connected Serial Interfaces
How To Earn Cisco’s Firewall Specialist Certification
|
|
|
|
|
|
 |
|
