|
|
|
|
Home / Computers / Computer Certification
Cisco CCNA Certification: Static Routing Tutorial
By:Chris Bryant, CCIE #12933
In studying for your CCNA exam and preparing to earn this valuable certification, you may be tempted to spend little time studying static routing and head right for the more exciting dynamic routing protocols like RIP, EIGRP, and OSPF. This is an understandable mistake, but still a mistake. Static routing is not complicated, but it's an important topic on the CCNA exam and a valuable skill for real-world networking.
To create static routes on a Cisco router, you use the ip route command followed by the destination network, network mask, and either the next-hop IP address or the local exit interface. It's vital to keep that last part in mind - you're either configuring the IP address of the downstream router, or the interface on the local router that will serve as the exit interface.
Let's say your local router has a serial0 interface with an IP address of 200.1.1.1/30, and the downstream router that will be the next hop will receive packets on its serial1 interface with an IP address of 200.1.1.2/30. The static route will be for packets destined for the 172.10.1.0 network. Either of the following ip route statements would be correct.
R1(config)#ip route 172.10.1.0 255.255.255.0 200.1.1.2 (next-hop IP address)
OR
R1(config)#ip route 172.10.1.0 255.255.255.0 serial0 ( local exit interface)
You can also write a static route that matches only one destination. This is a host route, and has 255.255.255.255 for a mask. If the above static routes should only be used to send packets to 172.10.1.1., the following commands would do the job.
R1(config)#ip route 172.10.1.1 255.255.255.255 200.1.1.2 (next-hop IP address)
OR
R1(config)#ip route 172.10.1.1 255.255.255.255 serial0 ( local exit interface)
Finally, a default static route serves as a gateway of last resort. If there are no matches for a destination in the routing table, the default route will be used. Default routes use all zeroes for both the destination and mask, and again a next-hop IP address or local exit interface can be used.
R1(config)#ip route 0.0.0.0 0.0.0.0 200.1.1.2 (next-hop IP address)
OR
R1(config)#ip route 0.0.0.0 0.0.0.0 serial0 ( local exit interface)
IP route statements seem simple enough, but the details regarding the next-hop IP address, the local exit interface, default static routes, and the syntax of the command are vital for success on CCNA exam day and in the real world.
Article Source: http://www.dailynewarticles.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNA and CCNP tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages.
For a FREE copy of his latest e-books, “How To Pass The CCNA” and “How To Pass The CCNP”, visit the website and download your free copies. You can also get FREE CCNA and CCNP exam questions every day! Get your CCNA certification with The Bryant Advantage!
More Articles from Computer Certification Category:
Cisco CCNP Certification / BCMSN Exam Tutorial: Writing QoS Policy
Cisco CCNP / BCSI Exam Tutorial: Configuring EIGRP Packet Authentication
Cisco CCNP / BSCI Certification: Introduction To ISIS Terminology
What To Expect When Taking Your First Cisco Certification Exam
Cisco CCNA / CCNP Home Lab: Why You Need An ISDN Simulator
Be Certifiable! The Basics Of MCSE And MCP
Cisco CCNP / BCSI Exam Tutorial: Broadcasts And The IP Helper-Address Command
Webroot Window Washer
Cisco CCNA / CCNP Home Lab Tutorial: Using 2520 Routers
CCNA / CCNP Home Lab Tutorial: The VLAN.DAT File
Cisco CCNP / BCMSN Exam Tutorial: Changing Root Bridge Election Results
CCNP Certification / BCMSN Exam Tutorial: HSRP MAC Addresses And Timers
Cisco CCNP / BCMSN Exam Tutorial: Switches, QoS, And Cisco's Networking Model
Cisco CCNA Exam Tutorial: Troubleshooting Directly Connected Serial Interfaces
How To Earn Cisco’s Firewall Specialist Certification
|
|
