|
|
|
|
Home / Computers / Computer Certification
Cisco CCNP / BSCI Certification: The BGP Attribute “MED”
By:Chris Bryant, CCIE #12933
When you're preparing to pass the BSCI exam and earn your CCNP certification, one of the biggest challenges is learning BGP. BGP is totally different from any protocol you learned to earn your CCNA certification, and one of the differences is that BGP uses path attributes to favor one path over another when multiple paths to or from a destination exist.
Notice I said "to or from". In earlier free BGP tutorials, I discussed the BGP attributes "weight" and "local preference". These attributes are used to favor one path to a destination over another; for example, if BGP AS 100 has two paths to a destination in AS 200, these two attributes can be set in AS 100 to favor one path over another. But what if AS 100 wants to inform the routers in AS 200 as to which path it should use to reach a given destination in AS 100?
That's where the BGP attribute "Multi-Exit Discriminator", or MED, comes in. The MED value can be set in AS 100 to tell AS 200 which path it should use to reach a given network in AS 100.
As with many BGP attributes, the MED can be set with a route-map. What you need to watch is that there is no "set med" value in route maps. To change the MED of a path, you need to change the metric of that path. Let's say that there are two entry paths for AS 200 to use to reach destinations in AS 100. You want AS 200 to use the 100.1.1.0/24 path over the 100.2.2.0/24 path. First, identify the two paths with two separate ACLs.
R1(config)#access-list 22 permit 100.1.1.0 0.0.0.255
R1(config)#access-list 23 permit 100.2.2.0 0.0.0.255
Next, write a route-map that assigns a lower metric to the more-desirable path.
R1(config)#route-map PREFER_PATH permit 10
R1(config-route-map)#match ip address 22
R1(config-route-map)#set metric 100
R1(config-route-map)#route-map PREFER_PATH permit 20
R1(config-route-map)#match ip address 23
R1(config-route-map)#set metric 250
Finally, apply the route-map to the neighbor or neighbors.
R1(config-route-map)#router bgp 100
R1(config-router)#neighbor 22.2.2.2 route-map PREFER_PATH out
The key points to keep in mind is that while many BGP attributes prefer a higher value, the MED is basically an external metric - and a lower metric is preferred, just as with the protocols you've already studied to earn your CCNA certification.
Article Source: http://www.dailynewarticles.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (www.thebryantadvantage.com), home of free CCNA and CCNP tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages. Video courses and training, binary and subnetting help, and corporate training are also available. Pass the CCNA exam and BSCI exam with Chris Bryant, CCIE #12933!
For a copy of his FREE ebooks, “How To Pass The CCNA” and “How To Pass The CCNP”, visit the website and download your copies! Get your CCNP certification with The Bryant Advantage!
More Articles from Computer Certification Category:
Cisco CCNP Certification / BCMSN Exam Tutorial: Writing QoS Policy
Cisco CCNP / BCSI Exam Tutorial: Configuring EIGRP Packet Authentication
Cisco CCNP / BSCI Certification: Introduction To ISIS Terminology
What To Expect When Taking Your First Cisco Certification Exam
Cisco CCNA / CCNP Home Lab: Why You Need An ISDN Simulator
Be Certifiable! The Basics Of MCSE And MCP
Cisco CCNP / BCSI Exam Tutorial: Broadcasts And The IP Helper-Address Command
Webroot Window Washer
Cisco CCNA / CCNP Home Lab Tutorial: Using 2520 Routers
CCNA / CCNP Home Lab Tutorial: The VLAN.DAT File
Cisco CCNP / BCMSN Exam Tutorial: Changing Root Bridge Election Results
CCNP Certification / BCMSN Exam Tutorial: HSRP MAC Addresses And Timers
Cisco CCNP / BCMSN Exam Tutorial: Switches, QoS, And Cisco's Networking Model
Cisco CCNA Exam Tutorial: Troubleshooting Directly Connected Serial Interfaces
How To Earn Cisco’s Firewall Specialist Certification
|
|
