|
|
|
|
Home / Computers / Computer Certification
Cisco CCNP / BSCI Exam Tutorial: The Passive Interface Command And OSPF
By:Chris Bryant, CCIE #12933
To pass the BSCI exam and become a CCNP, you have to be aware of the proper use of passive interfaces. You learned about passive interfaces in your CCNA studies, but here we’ll review the basic concept and clear up one misconception regarding passive interfaces and OSPF.
Configuring an interface as passive will still allow the interface to receive routing updates, but the interface will no longer transmit them. While the command itself would make you think this command will be applied at the interface level, that is not the case. Below, we’ll configure ethernet0 as a RIP passive interface.
R1(config)#router rip
R1(config-router)#passive-interface ethernet0
Ethernet0 will no longer send RIP routing updates, but will accept them.
The passive interface concept is clear enough with RIP, IGRP, and EIGRP – all protocols that send routing update packets. But OSPF doesn’t send routing update packets – OSPF sends link state advertisements. It’s the inability of the passive interface command to stop LSAs that lead many to think that passive interfaces cannot be used with OSPF.
Even though OSPF does not sent "routing updates" in the form that RIP, IGRP, and EIGRP do, you can still configure an OSPF-enabled interface as passive in order to prevent OSPF traffic from exiting or entering that interface. No OSPF adjacency can be formed if one of the interfaces involved is a passive interface, and if you configure an OSPF-enabled interface as passive where an adjacency already exists, the adjacency will drop almost immediately.
Let's see that in action. R1 and R2 have an existing OSPF adjacency over their Ethernet interfaces. In an effort to reduce routing traffic, R1's e0 interface is configured as passive. The adjacency drops right away.
R1(config)#router ospf 1
R1(config-router)#passive-interface ethernet0
18:31:11: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Ethernet0 from FULL to DOWN, Neighbor Down: Interface down or detached
Knowing how to use the passive interface command is a vital part of being a CCNP, and of being a master networker. Good luck to you in both of these pursuits!
Article Source: http://www.dailynewarticles.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNP and CCNA tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages.
You can also join his RSS feed and visit his blog, which is updated several times daily with new Cisco certification articles, free tutorials, and daily CCNA / CCNP exam questions! Details are on the website.
For a FREE copy of his latest e-books, “How To Pass The CCNA” and “How To Pass The CCNP”, just visit the website! You can also get FREE CCNA and CCNP exam questions every day! Pass the CCNP exam with The Bryant Advantage!
More Articles from Computer Certification Category:
Cisco CCNP Certification / BCMSN Exam Tutorial: Writing QoS Policy
Cisco CCNP / BCSI Exam Tutorial: Configuring EIGRP Packet Authentication
Cisco CCNP / BSCI Certification: Introduction To ISIS Terminology
What To Expect When Taking Your First Cisco Certification Exam
Cisco CCNA / CCNP Home Lab: Why You Need An ISDN Simulator
Be Certifiable! The Basics Of MCSE And MCP
Cisco CCNP / BCSI Exam Tutorial: Broadcasts And The IP Helper-Address Command
Webroot Window Washer
Cisco CCNA / CCNP Home Lab Tutorial: Using 2520 Routers
CCNA / CCNP Home Lab Tutorial: The VLAN.DAT File
Cisco CCNP / BCMSN Exam Tutorial: Changing Root Bridge Election Results
CCNP Certification / BCMSN Exam Tutorial: HSRP MAC Addresses And Timers
Cisco CCNP / BCMSN Exam Tutorial: Switches, QoS, And Cisco's Networking Model
Cisco CCNA Exam Tutorial: Troubleshooting Directly Connected Serial Interfaces
How To Earn Cisco’s Firewall Specialist Certification
|
|
